The application team has reported latency issues that are causing the application to crash on the Linux server. The Linux administrator starts
troubleshooting and receives the following output:
Which of the following commands will improve the latency issue?
Correct Answer:
D
The best command to use to improve the latency issue is D. # echo ‘net.core.rmem max = 12500000’ >> /etc/sysctl.conf # echo ‘net.core.wmem_max = 12500000’ >> /etc/sysctl.conf # sysctl -p. This command will increase the size of the receive and send buffers for the network interface, which can improve the network performance and reduce packet loss. The sysctl command will apply the changes to the kernel parameters without rebooting the system.
The other commands are either incorrect or not suitable for this task. For example:
✑ A. # echo ‘net.core.net_backlog = 5000000’ >> /etc/sysctl.conf # sysctl -p # systemctl daemon-reload will try to increase the backlog queue for incoming connections, but this is not relevant for the latency issue. The systemctl daemon- reload command is also unnecessary, as it only reloads the systemd configuration files, not the kernel parameters.
✑ B. # ifdown eth0 # ip link set dev eth0 mtu 800 # ifup eth0 will try to change the maximum transmission unit (MTU) of the network interface to 800 bytes, but this is too low and may cause fragmentation and performance degradation. The default MTU for Ethernet is 1500 bytes, and it should not be changed unless there is a specific reason.
✑ C. # systemctl stop network # ethtool -g eth0 512 # systemctl start network will try to change the ring buffer size of the network interface to 512, but this is too small and may cause packet drops and latency spikes. The default ring buffer size for Ethernet is usually 4096 or higher, and it should be increased if there is a high network traffic.
A database administrator requested the installation of a custom database on one of the servers. Which of the following should the Linux administrator configure so the requested packages can be installed?
Correct Answer:
C
The Linux administrator should configure /etc/yum.repos.d/db.repo so that the requested packages can be installed. This file defines a custom repository for yum, which is a package manager for RPM-based systems. The file should contain information such as the name, baseurl, gpgcheck, and enabled options for the repository. By creating this file and enabling the repository, the administrator can use yum to install packages from the custom repository. The /etc/yum.conf file is the main configuration file for yum, but it does not define repositories. The /etc/ssh/sshd.conf file is the configuration file for sshd, which is a daemon that provides secure shell access to remote systems. The /etc/resolv.conf file is the configuration file for DNS resolution, which maps domain names to IP addresses. References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 19: Managing Packages and Software, page 559.
A Linux engineer needs to create a custom script, cleanup.sh, to run at boot as part of the system services. Which of the following processes would accomplish this task?
Correct Answer:
C
The process that will accomplish the task of creating a custom script to run at boot as part of the system services is:
✑ Create a unit file in the /etc/systemd/system/ directory. A unit file is a configuration
file that defines the properties and behavior of a systemd service. The systemd is a system and service manager that controls the startup and operation of Linux systems. The /etc/systemd/system/ directory is the location where the administrator can create and store custom unit files. The unit file should have a name that matches the name of the script, such as cleanup.service, and should contain the following sections and options:
✑ Run the command systemct1 enable cleanup. This command will enable the service and create the necessary symbolic links to start the service at boot.
✑ Run the command systemct1 is-enabled cleanup. This command will check the status of the service and confirm that it is enabled.
This process will create a custom script, cleanup.sh, to run at boot as part of the system services. This is the correct process to use to accomplish the task. The other options are incorrect because they either use the wrong directory for the unit file (/etc/default/, /etc/skel/, or /etc/sysctl.d/) or do not create a unit file at
all. References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 15: Managing System Services, pages 457-459.
A cloud engineer needs to block the IP address 192.168.10.50 from accessing a Linux server. Which of the following commands will achieve this goal?
Correct Answer:
B
The correct command to block the IP address 192.168.10.50 from accessing a Linux server is iptables -A INPUT -s 192.168.10.50 -j DROP. This command appends a rule to the INPUT chain that matches the source address 192.168.10.50 and jumps to the DROP target, which discards the packet. The other commands are incorrect because they either have invalid syntax, wrong parameters, or wrong order of arguments. References:
CompTIA Linux+ Study Guide, Fourth Edition, page 457-458.
A systems administrator is notified that the mysqld process stopped unexpectedly. The systems administrator issues the following command: sudo grep –i -r ‘out of memory’ /var/log
The output of the command shows the following:
kernel: Out of memory: Kill process 9112 (mysqld) score 511 or sacrifice child.
Which of the following commands should the systems administrator execute NEXT to troubleshoot this issue? (Select two).
Correct Answer:
AF
The free -h command can be used to check the amount of free and used memory in the system in a human-readable format. This can help to troubleshoot the issue of mysqld being killed due to out of memory. The vmstat -a 1 4 command can be used to monitor the system’s virtual memory statistics, such as swap usage, paging activity, and memory faults, every one second for four times. This can help to identify any memory pressure or performance issues that may cause out of memory errors. The nc -v 127.0.0.1 3306 command would attempt to connect to the MySQL server on port 3306 and display any diagnostic messages, but this would not help to troubleshoot the memory issue. The renice -15 $( pidof mysql ) command would change the priority of the mysql process to -15, but this would not prevent it from being killed due to out of memory. The lsblk command would display information about block devices, not memory usage. The killall -15 command would send a SIGTERM signal to all processes with a matching name, but this would not help to troubleshoot the memory issue. References: [CompTIA Linux+ (XK0-005) Certification Study Guide], Chapter 15: Managing Memory and Process Execution, pages 468-469.
